REINFORM | WHITE-BIB SHOW SHIRT SPECIFICATION SHEET DRAFT TEMPLATE — complete and approve with your technical team and factory. No dimensions, tolerances, grade rules or performance results are pre-approved. 1. DOCUMENT CONTROL Brand / technical contact: ____________________ Style code / season: ____________________ Description: long-sleeve white-bib show shirt with separately specified contrast body Revision / date / prepared by: ____________________ Sample ID / stage / base size / ordered size range: ____________________ Units (choose cm or inches): ______ Measurement condition: ____________________ Reference jacket / intended market, discipline and event: ____________________ Front drawing reference: ______ Back drawing reference: ______ Bib, collar, opening and cuff detail drawing references: ____________________ 2. MEASUREMENT RECORD Add each code below to the corresponding front/back/detail drawing. Confirm all methods. Add pattern-specific points and extra size columns as required. Record garment dimensions separately from wearer body measurements. A. Body length Method to agree: From the high shoulder point at the neck seam to the finished hem; identify the front/back method on the drawing. Base-size target: ______ Tolerance (+/-): ______ Other ordered sizes and targets: ____________________ Grade rule / size interval: ____________________ Sample actual before care: ______ After agreed care: ______ Correction / owner / next revision: ____________________ Approval status / reviewer / date: ____________________ B. Half chest Method to agree: Lay the closed garment flat and relaxed. State the distance below the armhole used for the side-to-side line. Base-size target: ______ Tolerance (+/-): ______ Other ordered sizes and targets: ____________________ Grade rule / size interval: ____________________ Sample actual before care: ______ After agreed care: ______ Correction / owner / next revision: ____________________ Approval status / reviewer / date: ____________________ C. Half waist Method to agree: Measure side to side at the waist line marked on the drawing; give its distance from the agreed reference point. Base-size target: ______ Tolerance (+/-): ______ Other ordered sizes and targets: ____________________ Grade rule / size interval: ____________________ Sample actual before care: ______ After agreed care: ______ Correction / owner / next revision: ____________________ Approval status / reviewer / date: ____________________ D. Half hem Method to agree: Measure the finished lower edge flat, with no added stretch; state how any curved hem is positioned. Base-size target: ______ Tolerance (+/-): ______ Other ordered sizes and targets: ____________________ Grade rule / size interval: ____________________ Sample actual before care: ______ After agreed care: ______ Correction / owner / next revision: ____________________ Approval status / reviewer / date: ____________________ E. Across shoulder Method to agree: Identify the two shoulder/sleeve seam junctions and the straight or curved measurement path. Base-size target: ______ Tolerance (+/-): ______ Other ordered sizes and targets: ____________________ Grade rule / size interval: ____________________ Sample actual before care: ______ After agreed care: ______ Correction / owner / next revision: ____________________ Approval status / reviewer / date: ____________________ F. Sleeve length Method to agree: Measure from the named shoulder point to the sleeve end; state explicitly whether the cuff is included. Base-size target: ______ Tolerance (+/-): ______ Other ordered sizes and targets: ____________________ Grade rule / size interval: ____________________ Sample actual before care: ______ After agreed care: ______ Correction / owner / next revision: ____________________ Approval status / reviewer / date: ____________________ G. Upper sleeve width Method to agree: Mark the measurement level below the armhole and measure flat across the relaxed sleeve. Base-size target: ______ Tolerance (+/-): ______ Other ordered sizes and targets: ____________________ Grade rule / size interval: ____________________ Sample actual before care: ______ After agreed care: ______ Correction / owner / next revision: ____________________ Approval status / reviewer / date: ____________________ H. Cuff opening and depth Method to agree: Record opening and depth separately. State whether the cuff is fastened and whether the opening is flat width or circumference. Base-size target: ______ Tolerance (+/-): ______ Other ordered sizes and targets: ____________________ Grade rule / size interval: ____________________ Sample actual before care: ______ After agreed care: ______ Correction / owner / next revision: ____________________ Approval status / reviewer / date: ____________________ I. Neck opening Method to agree: Mark the start/end points, fastening position and path on a detail drawing; distinguish finished opening from body neck measurement. Base-size target: ______ Tolerance (+/-): ______ Other ordered sizes and targets: ____________________ Grade rule / size interval: ____________________ Sample actual before care: ______ After agreed care: ______ Correction / owner / next revision: ____________________ Approval status / reviewer / date: ____________________ J. Collar height Method to agree: Measure the finished collar from its joining seam to its top edge at the marked location; note any front/back difference. Base-size target: ______ Tolerance (+/-): ______ Other ordered sizes and targets: ____________________ Grade rule / size interval: ____________________ Sample actual before care: ______ After agreed care: ______ Correction / owner / next revision: ____________________ Approval status / reviewer / date: ____________________ K. Front opening Method to agree: Mark the top and bottom of the usable opening. Record the cover width and fastening reference separately. Base-size target: ______ Tolerance (+/-): ______ Other ordered sizes and targets: ____________________ Grade rule / size interval: ____________________ Sample actual before care: ______ After agreed care: ______ Correction / owner / next revision: ____________________ Approval status / reviewer / date: ____________________ L. Bib width Method to agree: Set a named horizontal level on the front drawing and measure between the white-panel edges without stretching the body. Base-size target: ______ Tolerance (+/-): ______ Other ordered sizes and targets: ____________________ Grade rule / size interval: ____________________ Sample actual before care: ______ After agreed care: ______ Correction / owner / next revision: ____________________ Approval status / reviewer / date: ____________________ M. Bib depth Method to agree: Measure from the marked collar joining point to the lower bib edge. Show the exact path on the front drawing. Base-size target: ______ Tolerance (+/-): ______ Other ordered sizes and targets: ____________________ Grade rule / size interval: ____________________ Sample actual before care: ______ After agreed care: ______ Correction / owner / next revision: ____________________ Approval status / reviewer / date: ____________________ N. Armhole Method to agree: Agree a flat-depth or seam-path method and show it on the drawing. Do not compare values taken by different methods. Base-size target: ______ Tolerance (+/-): ______ Other ordered sizes and targets: ____________________ Grade rule / size interval: ____________________ Sample actual before care: ______ After agreed care: ______ Correction / owner / next revision: ____________________ Approval status / reviewer / date: ____________________ 3. MATERIAL AND CONSTRUCTION REFERENCES Complete one record per material or trim. White bib does not imply an all-white body. Part: bib / body / sleeve / collar / cuff / support layer / fastening / other Reference and supplier: ______ Composition / weight: ______ Colour reference / approved swatch: ______ Care requirement: ______ Join or seam location: ______ Seam type / allowance / stitch / thread: ______ Unresolved detail / reviewer / due date: ____________________ Repeat part record as needed: ____________________ 4. SAMPLE AND CHANGE LOG Review jacket-window coverage, collar contact, cuffs, movement and tuck-in. Agree lighting/underlayers for white coverage and the care procedure before review. Date / sample revision / point code: ____________________ Previous target / actual result / requested correction: ____________________ Affected drawing, material or seam reference: ____________________ Retest result / reviewer / approval status: ____________________ Repeat change record as needed: ____________________ 5. PRODUCTION HANDOFF Final sheet revision and drawing references: ____________________ Approved sample ID / material and trim references: ____________________ Remaining open items (do not mark approved until resolved): ____________________ Buyer approval / factory acknowledgement / dates: ____________________ Artwork, label, packing and order documents attached: ____________________ Order per finished style / colour / size: ____________________ Destination country / US state if relevant / delivery requirement: ____________________ MOQ: 300 pieces per style, per colour. Confirm contrast colourway counting. Sampling: 7–10 working days. Bulk: 30–45 working days from the agreed start. Revisions and transit are separate. Confirm the scope and schedule in the quotation. This is a blank development worksheet, not a finished tech pack or size chart. Use with your completed drawings, material selection and written sample approval. Product guide: https://reinformm.com/products/show-shirts/white-bib-long-sleeve-show-shirt